Cooler Master Evo with 2 fans at push/pull
i have used CM evo for my processor for a few days..the temps weren't bad..
while gaming(Run, Saboteur) for 2 hours+ =54C
maximum load=65C (15-20 mins with IBT)
OCed to 3.9GHz and maximum load=80C
i recently added 2 CM xtraflo red LED fans in push pull config..and here's the new result:
after playing total war shogun 2 for 2 hours+ =51C
i havent OCed my processor yet after i got 2 of these fans
and my casing airflow(negetive pressure) also increased as i now have 5 90cfm silent fans from CM...
so what do you guys think??
Wow thats a pretty Significant drop in temps. The case pressure helps too I guess.
The Coolermaster R4s Dropped my GPU temp by ~2-4C, and they are much more silent and looks better than Thunderblades too.
But, how far can u go with that non k 3550?
Did u try higher than 3.9?
Indeed they are. But still there is a humming sound if you have like 7 of them running at 70% Speed. Other than that even the two 200mm fans in my case @ 100% speeds are louder than 7 R4s @ 70% Speeds.
Originally Posted by dipanzan
EDIT : Just checked, they are a bit louder than the two 200mms, but they make a different sound, its more of an humming sound rather than what you get from thunderblades. But I've had 3 R4s and 3 TBs at the same time, the R4s were alot more quieter than the TBs.
Last edited by Rakin7; September 13th, 2012 at 16:50.
i can go upto 3.9...and with bios update 4.1 is possible (thats what i've heard)..i'm going to do that after my prof...i'll try to update this thread then...this 3550 is the hottest processor of all the ivy processors so i guess thats a great result
Originally Posted by Mohiuddin
- - - Updated - - -
did you put the fan just beside the gpu?? i mean in the side panel??
Originally Posted by eXcavator
hmmm... thats kinda weird for me... are e8400 more hotter than ivy bridge processors... i too use an evo 212 with push[default] and pull[xtraflow] with 0 case fans [i know, i have a crappy case and slots for only 80mm fans so yeah] BUT side panel removed and here are my temps...
CPU: E8400 @ 3.6GHz
TIM: default CM tim.
idle temps: 51c
load temps [prime95]: 74-75c
[OCCT] normal: 76-78c
is that completely cause of the airflow of my case??
it might be your casing..if the airflow isnt sufficient (into and out of the case) 100 cooling fans mounted to the EVO or any other cooler wont do any good...but what i know about your processor is..it's known to have faulty sensors..if you google you'll see what i mean...so that might be your problem as well
Originally Posted by zunaid
did you get your evo from binary..they use a lot of TIM..which actually doesnt help keeping the temp down
and if possible reapply TIM (clean and reapply) and then place cooler..make sure it just sits over the cpu correctly..not too tight not too loose (binary people tend to get the screws too tight, which may end up damaging your motherboard)
Last edited by terrygr8_007; September 13th, 2012 at 18:36.
Fan ta kothai pawa jai? and price koto ? newegg showing $36, so should it be around $40? if so then I will buy an unboxed processor and this fan.
I'm getting positive reviews from newegg.
thats actually below 40$...2800 or 2750 BDT from binary logic with the stock fan..and if you buy another fan make sure you get the Xtraflo red LED one..it spins faster and pushes more air...also dont tell binary people about this (i'm afraid they'll increase the price if they know it)
Originally Posted by Hamilton
the stock fan is also xtraflo non-LED version, which pushes ~83 cfm air, same goes for blue led one..but the red LED spins at 2200 RPM and pushes ~93 cfm air..i specifically wanted the red one for this reason
fan price 850 tk for the xtraflo one and 650 tk for R4
Thank you very much XD
Originally Posted by terrygr8_007
Last edited by Rakin7; September 13th, 2012 at 21:22.
nop 212Evo has a Xtraflow. 212+ had a Blademaster.
Originally Posted by eXcavator
I have the same CPU and same cooler, my room temperature is around 25 ish due to AC. so can u give me some idea about the idle temp and temp at full load? i use a dokker with two intake fans in front and bottom and two exhaust in top and rear. i am asking these coz i had a hard time mounting it and applied thermal grease more than needed.
Originally Posted by @bhi
By war1oc in forum Others PC Hardware
Last Post: August 15th, 2012, 22:47
By Dee in forum Shop - Gadgets
Last Post: February 26th, 2012, 22:02
By VIPERS in forum Shop - Gadgets
Last Post: February 26th, 2012, 05:46
By EBL.Mantis in forum Shop - Gadgets
Last Post: November 10th, 2011, 20:44
By Dee in forum Others PC Hardware
Last Post: January 25th, 2011, 22:40
Tags for this Thread
Page generated in 0.30933 seconds with 15 queries.